Sprint Magic Box Serial Logs
Written 2019-03-23
The three pin header on the relay board has
a 3.3v 115200 baud serial port. Sadly, it's
using U-Boot Secure Boot.
U-Boot SPL 2015.10 (Jun 21 2017 - 15:40:14)
U-Boot 2015.10 (Jun 21 2017 - 15:40:14 +0100)
CPU: Freescale i.MX6SX rev1.2 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 39C
Reset cause: POR
Board: MX6SX AIRUNITY
BoardId: 0005
Watchdog enabled
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0
PCI: pcie phy link never came up
In: serial
Out: serial
Err: serial
Exit emergency shutdown mode
Writing debounce period of 30 seconds to TI battery chip is OK.
SECURE BOOT running, Boot prompt is disabled
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Booting from MMC...
switch to partitions #0, OK
mmc0(part 0) is current device
externalconfig: banktoboot=0
externalconfig: runapp=1
externalconfig: bootattempts bank0=7
externalconfig: bootattempts bank1=0
WARNING - Bank 0 previously failed to boot. Attempting again (8/15)
fallbackcheck: banktoboot=0
fallbackcheck: bootattempts bank0=8
fallbackcheck: bootattempts bank1=0
dtb=airspan-0005.dtb
37665 bytes read in 122 ms (300.8 KiB/s)
6588448 bytes read in 435 ms (14.4 MiB/s)
Kernel image @ 0x82000000 [ 0x000000 - 0x648820 ]
## Flattened Device Tree blob at 88000000
Booting using the fdt blob at 0x88000000
Loading Device Tree to bfc24000, end bfc30320 ... OK
Starting kernel ...
[ 0.086684] reg_fixed_voltage_probe: skipped regulators:regulator@6 from setting HIGH
[ 0.142899] Inserting airspan_gpio module
[ 0.147712] mxsfb-spi-it8951 spidisp@0: allocated fb @ paddr=0xAA080000, size=518400. yres[540], lineLen[960]
[ 0.185820] imx6sx-pinctrl 20e0000.iomuxc: pin MX6SX_PAD_GPIO1_IO04 already requested by 2020000.serial; cannot claim for 22a0000.serial
[ 0.198150] imx6sx-pinctrl 20e0000.iomuxc: pin-9 (22a0000.serial) status -22
[ 0.205239] imx6sx-pinctrl 20e0000.iomuxc: could not request pin 9 (MX6SX_PAD_GPIO1_IO04) from group uart6wifiap on device 20e0000.iomuxc
[ 0.217713] imx-uart 22a0000.serial: Error applying setting, reverse things back
[ 0.229848] Error: Driver 'imx-ipuv3' is already registered, aborting...
[ 0.236728] DEBUG: SPIDEV Initialised! 0
[ 0.242600] spidev spi2.0: buggy DT: spidev listed directly in DT
[ 0.467514] my_cfb_imageblit() called
[ 1.143218] caam_jr 2101000.jr0: 20000b11: CCB: desc idx 11: AES: Mode error.
[ 1.150701] alg: aead: encryption failed on test 1 for rfc4106-gcm-aes-caam: ret=-536873745
[ 1.159768] caam_jr 2101000.jr0: 20000c11: CCB: desc idx 12: AES: Mode error.
[ 1.167011] alg: aead: encryption failed on test 1 for gcm-aes-caam: ret=-536874001
[ 1.220880] snvs-secvio 20cc000.caam-snvs: can't get snvs clock
[ 1.237143] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 1.560270] imx6q-pcie 8ffc000.pcie: phy link never came up
[ 1.566134] imx6q-pcie 8ffc000.pcie: failed to initialize host
[ 1.595032] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 1.603843] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
INIT: version 2.88 booting
Starting udev
bootlogd: cannot allocate pseudo tty: No such file or directory
ALSA: Restoring mixer settings...
/usr/sbin/alsactl: load_state:1729: No soundcards found...
INIT: Entering runlevel: 3
Configuring network interfaces... [ 3.917366] m25p80 spi1.0: unrecognized JEDEC id bytes: 00, 0, 0
done.
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd
done.
Starting rpcbind daemon...done.
Starting advanced power management daemon: No APM support in kernel
(failed.)
Starting HOSTAP Daemon: Configuration file: /etc/hostapd.conf
Could not read interface wlan0 flags: No such device
nl80211: Driver does not support authentication/association or connect commands
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
Could not read interface wlan0 flags: No such device
nl80211 driver initialization failed.
wlan0: interface state UNINITIALIZED->DISABLED
wlan0: AP-DISABLED
hostapd_free_hapd_data: Interface wlan0 wasn't started
Starting IrDA: irattach fail
Starting ntpd: done
Starting syslogd/klogd: done
[ ok ]rting Avahi mDNS/DNS-SD Daemon: avahi-daemon
Starting Telephony daemon
Starting Linux NFC daemon
Starting Lighttpd Web Server: lighttpd.
***************************************************
BoardId = 0005
BoardId Name = AU545
Image = airunity
Kernel cmdline = root=/dev/mmcblk0p2 rootwait console=ttymxc0,115200 runapp=yes envoffset=0x48000 bootversion=65.1.23.0 raid=noautodetect pci=nomsi ahci_imx.hotplug=1 quiet
***************************************************
Start init SUCCESS.
Inserting module spi_it8951
[ 14.884690] ALERT: Openning file handle on: /dev/spidev2.0
[ 14.896978] Initialised it8951_init 1511
Initialising spi_it8951
[ 15.450692] Initialised Device it8951_initdev 557
Warning: Old and New Firmware versions match: Airspan.v.0.18
INFO: Display Width: 960
INFO: Display Height: 540
INFO: Display FWVersion: Airspan.v.0.18
INFO: Display LUTVersion: 320_R117_AF8301_
[ 15.532901] Error: IT8951 unable to open: /dev/mtd0ro it8951_read_epd_flash 417
[ 15.540282] Error: EPD flash read failed
[ 15.554171] Error: IT8951 unable to open: /dev/mtd0ro it8951_read_epd_flash 417
[ 15.561553] Error: EPD flash read failed
file is not updated: file version [12] batt serial number[12]
Data Flash Parameters update not required.
Start init SUCCESS.
Inserting module tamperdetect
[ 18.216668] Error: i2c_transfer: -5 tamperdetect_get_cmd 927
[ 18.222385] Error: Failed to get fw version tamperdetect_get_fwver 1025
[ 18.229034] Error: Invalid FW Version tamperdetect_initdev 716
[ 18.234887] Error: Initialisation Failed: 3
Initialising tamperdetect
Error: tamperdetect Driver failed to initialise: Retry: 1
Module tamperdetect present - removing first
[ 18.353840] Exited tamperdetect_exit 2549
Inserting module tamperdetect
[ 18.374874] Error: i2c_transfer: -5 tamperdetect_get_cmd 927
[ 18.380636] Error: Failed to get fw version tamperdetect_get_fwver 1025
[ 18.387324] Error: Invalid FW Version tamperdetect_initdev 716
[ 18.393213] Error: Initialisation Failed: 3
Initialising tamperdetect
Error: tamperdetect Driver failed to initialise: Retry: 2
Module tamperdetect present - removing first
[ 18.502064] Exited tamperdetect_exit 2549
Inserting module tamperdetect
[ 18.523182] Error: i2c_transfer: -5 tamperdetect_get_cmd 927
[ 18.528935] Error: Failed to get fw version tamperdetect_get_fwver 1025
[ 18.535619] Error: Invalid FW Version tamperdetect_initdev 716
[ 18.541519] Error: Initialisation Failed: 3
Initialising tamperdetect
Error: tamperdetect Driver failed to initialise: Retry: 3
Module tamperdetect present - removing first
[ 18.649968] Exited tamperdetect_exit 2549
Inserting module tamperdetect
[ 18.670924] Error: i2c_transfer: -5 tamperdetect_get_cmd 927
[ 18.676676] Error: Failed to get fw version tamperdetect_get_fwver 1025
[ 18.683372] Error: Invalid FW Version tamperdetect_initdev 716
[ 18.689262] Error: Initialisation Failed: 3
Initialising tamperdetect
Error: tamperdetect Driver init retry count exceeded!
Board type is AU545, eNB power driven by MAINS so keep eNB power turning ON
choice3, gpio_bank2, gpio_bin1, dir_val0, value1
gpioSetupPinMode 2:1 (1 <= bank =< 8, 0 <= bin <= 31)
gpioRegisterBankPin 2:1 (1 <= bank =< 8, 0 <= bin <= 31)
registerGpioBankPin: 2:1 pin is registered
choice3, gpio_bank7, gpio_bin3, dir_val0, value0
gpioSetupPinMode 7:3 (1 <= bank =< 8, 0 <= bin <= 31)
gpioRegisterBankPin 7:3 (1 <= bank =< 8, 0 <= bin <= 31)
registerGpioBankPin: 7:3 pin is registered
choice3, gpio_bank4, gpio_bin23, dir_val0, value1
gpioSetupPinMode 4:23 (1 <= bank =< 8, 0 <= bin <= 31)
gpioRegisterBankPin 4:23 (1 <= bank =< 8, 0 <= bin <= 31)
registerGpioBankPin: 4:23 pin is registeredChoosing the image
airspan: 65.1.23.0
NFSTEST=
airspan: RUNAPP = yes
Mount /config, /calibration and /archive partitions
Showing Sprint Logo
/dev/emmc1 has journal
/dev/emmc2 has journal
/dev/emmc3 has journal
Synchronising authentication credentials
Backup file not found
Reboot reason: Power-cycle (WDOG1_WRSR=0x0010: POR bit=1)
Starting background process to kick watchdog for 5 minutes (10s kick) until procmgr takes over
Starting hardware watchdog loop for 30 iterations with 10000000 usec delay...
X.Org X Server 1.14.4
Release Date: 2013-10-31
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.13.0-110-generic x86_64
Current Operating System: Linux airunity 4.1.15 #1 SMP Fri Jun 30 18:16:40 BST 2017 armv7l
Kernel command line: root=/dev/mmcblk0p2 rootwait console=ttymxc0,115200 runapp=yes envoffset=0x48000 bootversion=65.1.23.0 raid=noautodetect pci=nomsi ahci_imx.hotplug=1 quiet
Build Date: 02 March 2017[ 21.011314] my_cfb_fillrect() called
09:32:02AM
Current version of pixman: 0.32.6
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Mar 16 21:45:05 2019
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
Initializing built-in extension Generic Event Extension
Initializing built-in extension SHAPE
Initializing built-in extension MIT-SHM
Initializing built-in extension XInputExtension
Initializing built-in extension XTEST
Initializing built-in extension BIG-REQUESTS
Initializing built-in extension SYNC
Initializing built-in extension XKEYBOARD
Initializing built-in extension XC-MISC
Initializing built-in extension XFIXES
Initializing built-in extension RENDER
Initializing built-in extension RANDR
Initializing built-in extension COMPOSITE
Initializing built-in extension DAMAGE
Initializing built-in extension MIT-SCREEN-SAVER
Initializing built-in extension DOUBLE-BUFFER
Initializing built-in extension DPMS
Initializing built-in extension X-Resource
Initializing built-in extension XVideo
Initializing built-in extension XVideo-MotionCompensation
Initializing built-in extension XFree86-VidModeExtension
Initializing built-in extension XFree86-DGA
Initializing built-in extension XFree86-DRI
Initializing built-in extension DRI2
Loading extension GLX
App Param = 127.0.0.1, 9093, 9092, /bs/font/, 0005, /bs/images/, yes, 960, 540, yes
2019-03-16 21:45:15 DEBUG ScreenView - /bs/images/animatable/network
2019-03-16 21:45:17 INFO ViewNotification - addViewNotificationListener called
2019-03-16 21:45:18 INFO CommNotification - addCommNotificationListener called
Comms Param = 127.0.0.1, 9093, 9092, /bs/font/, 0005, /bs/images/, yes, 960, 540, yes
2019-03-16 21:45:19 DEBUG UdpServer - UDPServer listening on port 9093
2019-03-16 21:45:19 DEBUG UpdateDisplay - UDP server socket open on port 9093
2019-03-16 21:45:19 DEBUG AirUnityServiceImpl - irelayCommClient created
2019-03-16 21:45:19 DEBUG UpdateDisplay - UDP client socket connected to 127.0.0.1 on port 9092
2019-03-16 21:45:19 DEBUG StatusIndicationSender - New Status Indication scheduling being used