Casa Systems B41 Femtocell Console and Fastboot

Casa Systems B41 Femtocell has a 4-pin serial console.

From left to right:

1. brown - Ground
2. red - RX(to device)
3. orange - TX(from device)
4. yellow - 3.3v

Configuration is 115200, 8N1.

During startup, you'll see the Android bootloader start, then a prompt:

[170] Press 1 to enable fast boot mode...

where you can indeed press 1 to enable fast boot mode which is accessible over the adjacent USB port. However, the bootloader is locked, so if you continued booting normally...

You'd next see what appears to be an Android Linux 3.10.84-perf kernel booting up.

Eventually, you'll see an OpenWrt logo, as there appears to be a separate CPU to run an MTK build of OpenWrt. This is used for both WiFi backhaul and to stand up an access point for commissioning.

Here's the entire log of a bootup:

B -     60847 - SBL1, Start
B -     60878 - scatterload_region && ram_init, Start
D -        30 - scatterload_region && ram_init, Delta
B -     71858 - Enable tsens
B -     72376 - tsensResult:=0 tsensTemp:=27
B -     72773 - Clock_BranchEnable
B -     76006 - Clock_MuxInit
B -     78629 - pm_device_init, Start
B -     81953 - boot_fsm_cdt_init, Start
D -    356026 - boot_fsm_cdt_init, Delta
B -    441609 - pm_fsm9055pdm_config
B -    442097 - boot_pm_driver_init, Start
B -    445940 - Clock_BranchEnable
B -    448960 - Clock_MuxInit
D -      5673 - boot_pm_driver_init, Delta
B -    455334 - pm_set_based_on_mode, Start
D -         0 - pm_set_based_on_mode, Delta
B -    462929 - pm_adjust_based_on_cpr, Start
D -        30 - pm_adjust_based_on_cpr, Delta
P -      1127 - pm_get_cx_vout (mv)
D -         0 - pm_device_init, Delta
B -    477386 - clock_init, Start
D -     26443 - clock_init, Delta
B -    507154 - boot_flash_init, Start
D -    985089 - boot_flash_init, Delta
B -   1492334 - boot_set_partition_id, Start
D -        91 - boot_set_partition_id, Delta
B -   1497336 - boot_fsm_cdt_init, Start
D -    146491 - boot_fsm_cdt_init, Delta
B -   1647396 - sbl1_hw_platform_pre_ddr, Start
D -         0 - sbl1_hw_platform_pre_ddr, Delta
B -   1653100 - sbl1_ddr_set_params, Start
D -       762 - sbl1_ddr_set_params, Delta
B -   1660542 - sbl1_ddr_init, Start
B -   1663775 - CHIP ID = 0x100 MSM Version = 0x10000
B -   1668472 - Board Type = 0x8 Version = 0x10000
B -   1672925 - DDR Frequency = 450000 kHz
B -   1678232 - Start DDR RCW Training
B -   1680397 - DDR RCW Training Results Start=0x07070707 Coarse=0x00002222 Fine=0x38383438
B -   1688022 - DDR CH0 Start Address:0x00000000_00000000 Size:0x400 MBytes
D -     30744 - sbl1_ddr_init, Delta
B -   1723890 - sbl1_tlmm_init, Start
D -        91 - sbl1_tlmm_init, Delta
B -   1724256 - Image Load, Start
B -   1739659 - Tz Execution, Start
D -    218837 - Tz Execution, Delta
B -   1982225 - Image Load, Start
B -   1982408 - Image Load, Start
B -   1982439 - Image Load, Start
B -   2000891 - sbl1_efs_handle_cookies, Start
D -       579 - sbl1_efs_handle_cookies, Delta
B -   2002782 - SBL1, End
Android Bootloader - UART_DM Initialized!!!
[0] welcome to lk
[0] Casa Systems Inc.
[10] platform_init()
[20] target_init()
[30] SDHC Running at 200 MHz
[70] SDHC Running in HS200 mode
[90] Done initialization of the card
[110] scm call to check secure boot fuses failed
[140] Neither 'config' nor 'frp' partition found
[170] Press 1 to enable fast boot mode...
[270] Trying to use 'boot_1' image...
[290] Loading (boot) image (30670848): start
[520] Loading (boot) image (30670848): done
[540] use_signed_kernel=0, is_unlocked=0, is_tampered=0.
[580] Uncpmpressed kernel in use
[590] Kernel image not patched..Unable to locate dt offset
[880] DTB Total entry: 20, DTB version: 3
[900] Using DTB entry 0x00000100/00000000/0x00010008/0 for device 0x00000100/00010000/0x00010008/0
[950] cmdline: root=/dev/ram0 rw rdinit=/sbin/init console=ttyHSL0,115200n8 earlyprintk maxcpus=4 coherent_pool=3M mem=196M@0x03c00000 mem=360M@0x29800000 vmalloc=512M androidboot.emmc=true androidboot.serialno=59d437a7 androidboot.baseband=msm cs_version=1 bun[1090] Updating device tree: start
[1130] Updating device tree: done
[1150] booting linux @ 0x3c08000, ramdisk @ 0x4d00000 (25910766), tags/device tree @ 0x4c00000
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.84-perf (user@qaserver2) (gcc version 5.4.1 20161213 (Linaro GCC 5.4-2017.01) ) #1 SMP PREEMPT Fri Apr 9 11:17:49 CEST 2021
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=50c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Qualcomm Technologies, Inc. FSM 9010 (Flattened Device Tree), model: Qualcomm Technologies, Inc. FSM9010 MTP
[    0.000000] Ignoring memory range 0x0 - 0x3c00000
[    0.000000] Ignoring memory range 0x0 - 0x3c00000
[    0.000000] cma: Found qsecom_region, memory base 0x00000000, size 0 MiB, limit 0x15000000
[    0.000000] cma: CMA: reserved 16 MiB at 0x0f000000 for default region
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] PERCPU: Embedded 12 pages/cpu @c314e000 s28608 r8192 d12352 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 141944
[    0.000000] Kernel command line: root=/dev/ram0 rw rdinit=/sbin/init console=ttyHSL0,115200n8 earlyprintk maxcpus=4 coherent_pool=3M mem=196M@0x03c00000 mem=360M@0x29800000 vmalloc=512M androidboot.emmc=true androidboot.serialno=59d437a7 androidboot.baseband=msm cs_version=1 bundle=1
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 513772K/569344K available (4887K kernel code, 433K rwdata, 2456K rodata, 215K init, 878K bss, 55572K reserved, 368640K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xcc800000 - 0xff000000   ( 808 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xcc400000   ( 196 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf800000 - 0xbfe00000   (   6 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0733ff4   (7344 kB)
[    0.000000]       .init : 0xc0734000 - 0xc0769fc0   ( 216 kB)
[    0.000000]       .data : 0xc076a000 - 0xc07d6758   ( 434 kB)
[    0.000000]        .bss : 0xc07d681c - 0xc08b20c8   ( 879 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] processor id specified, in device tree 5
[    0.000000] Architected cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[    0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: 32 bits at 19MHz, resolution 52ns, wraps every 223696213963ns
[    0.000000] Console: colour dummy device 80x30
[    0.000246] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000261] pid_max: default: 32768 minimum: 301
[    0.000464] Mount-cache hash table entries: 512
[    0.001334] Initializing cgroup subsys debug
[    0.001347] Initializing cgroup subsys freezer
[    0.001386] CPU: Testing write buffer coherency: ok
[    0.001704] /cpus/cpu@0 missing clock-frequency property
[    0.001722] /cpus/cpu@1 missing clock-frequency property
[    0.001739] /cpus/cpu@2 missing clock-frequency property
[    0.001757] /cpus/cpu@3 missing clock-frequency property
[    0.001772] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.001843] Setting up static identity map for 0xc049c5f8 - 0xc049c644
[    0.006732] MSM Memory Dump table set up
[    0.007739] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.008629] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.009502] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.009646] Brought up 4 CPUs
[    0.009673] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.009681] CPU: All CPU(s) started in SVC mode.
[    0.010649] devtmpfs: initialized
[    0.024505] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3
[    0.025476] pinctrl core: initialized pinctrl subsystem
[    0.025796] regulator-dummy: no parameters
[    0.026674] NET: Registered protocol family 16
[    0.030503] DMA: preallocated 3072 KiB pool for atomic coherent allocations
[    0.031553] stub-regulator-1v: 1000 mV normal idle 
[    0.031876] stub-regulator-1.8v: 1800 mV normal idle 
[    0.032216] stub-regulator-0.95v: 950 mV normal idle 
[    0.032540] stub-regulator_vdd_mx: 0 <--> 0 mV at 0 mV normal idle 
[    0.032882] stub-regulator_3.3v: 3200 mV normal idle 
[    0.040705] gdsc_pcie_0: normal idle 
[    0.041073] gdsc_pcie_1: normal idle 
[    0.042588] socinfo_print: v0.9, id=256, ver=1.0, raw_id=2378, raw_ver=0, hw_plat=8, hw_plat_ver=65536
[    0.042588]  accessory_chip=0, hw_plat_subtype=0, pmic_model=2147483647, pmic_die_revision=0 foundry_id=1
[    0.042620] invalid MAC address in efuse
[    0.042642] invalid MAC address in efuse
[    0.042702] add_danipc_property: adding danipc DT prop dl-bufs=<0x24000000 0x5800000>
[    0.042715] add_danipc_property: adding danipc DT prop ul-bufs=<0x23800000 0x800000>
[    0.043691] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.043703] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.043863] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.043887] platform fc4281d0.qcom,mpm: Driver mpm-v2 requests probe deferral
[    0.044347] clock-dummy qcom,rpmcc.7: Registered DUMMY provider.
[    0.048078] qcom,gcc-fsm9010 fc400000.qcom,gcc: Registered GCC clocks
[    0.050743] sps:sps is ready.
[    0.070987] bio: create slab  at 0
[    0.072044] dummy_vreg: no parameters
[    0.072406] vgaarb: loaded
[    0.072823] usbcore: registered new interface driver usbfs
[    0.072894] usbcore: registered new interface driver hub
[    0.073034] usbcore: registered new device driver usb
[    0.074241] ION heap system created
[    0.074353] ION heap qsecom created at 0x0f000000 with size 800000
[    0.075259] pcie:pcie_init.
[    0.077123] Switching to clocksource arch_sys_counter
[    0.105289] NET: Registered protocol family 2
[    0.106178] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.106236] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.106281] TCP: Hash tables configured (established 2048 bind 2048)
[    0.106353] TCP: reno registered
[    0.106371] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.106405] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.106656] NET: Registered protocol family 1
[    0.107059] RPC: Registered named UNIX socket transport module.
[    0.107070] RPC: Registered udp transport module.
[    0.107079] RPC: Registered tcp transport module.
[    0.107088] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.107380] Trying to unpack rootfs image as initramfs...
[    2.822403] Freeing initrd memory: 25300K (c1100000 - c29b5000)
[    2.825456] ftr_probe: BoardId = 0x33
[    3.472318] error setting kswapd cpu affinity mask
[    3.472553] bounce pool size: 64 pages
[    3.483313] fuse init (API version 7.23)
[    3.483832] msgmni has been set to 364
[    3.486010] NET: Registered protocol family 38
[    3.486278] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    3.486290] io scheduler noop registered
[    3.486300] io scheduler deadline registered
[    3.486322] io scheduler row registered
[    3.486504] io scheduler cfq registered (default)
[    3.486515] io scheduler test-iosched registered
[    3.490475] msm_serial: driver initialized
[    3.490640] msm_serial_hsl_probe: detected port #0 (ttyHSL0)
[    3.490668] msm_serial_hsl_probe: Bus scaling is disabled
[    3.490787] f9920000.serial: ttyHSL0 at MMIO 0xf9920000 (irq = 128) is a MSM
[    3.490851] msm_hsl_console_setup: console setup on port #0
[    4.221978] console [ttyHSL0] enabled
[    4.226012] msm_serial_hsl_probe: detected port #1 (ttyHSL1)
[    4.231282] msm_serial_hsl_probe: Bus scaling is disabled
[    4.236759] f991d000.serial: ttyHSL1 at MMIO 0xf991d000 (irq = 127) is a MSM
[    4.243966] msm_serial_hsl_init: driver initialized
[    4.259317] diag: In socket_open_server, socket not initialized for MODEM_DCI
[    4.264204] diag: In socket_open_server, socket not initialized for LPASS_DATA
[    4.266336] diag: In socket_open_server, socket not initialized for LPASS_CNTL
[    4.266418] diag: In socket_open_server, socket not initialized for WCNSS_DCI
[    4.267905] diag: In socket_open_server, socket not initialized for SENSORS_DCI
[    4.268029] diag: In socket_open_server, socket not initialized for WCNSS_CNTL
[    4.268112] diag: In socket_open_server, socket not initialized for SENSORS_DATA
[    4.269129] diag: In socket_open_server, socket not initialized for MODEM_DATA
[    4.269181] diag: In socket_open_server, socket not initialized for LPASS_DCI
[    4.272286] diag: In socket_open_server, socket not initialized for SENSORS_CNTL
[    4.272342] diag: In socket_open_server, socket not initialized for WCNSS_DATA
[    4.273344] diag: In __diag_cntl_socket_init, cntl socket is not initialized, ret: -97
[    4.278342] diag: In socket_open_server, socket not initialized for MODEM_CNTL
[    4.283354] brd: module loaded
[    4.287301] loop: module loaded
[    4.287644] QSEECOM: qseecom_probe: qseecom.qsee_version = 0x405000
[    4.287689] QSEECOM: qseecom_probe: qseecom.appsbl_qseecom_support = 0x0
[    4.287695] QSEECOM: qseecom_probe: no-clock-support=0x1
[    4.287696] QSEECOM: qseecom_probe: qsee reentrancy support phase is not defined, setting to default 0
[    4.287732] QSEECOM: qseecom_probe: secure app region addr=0x13500000 size=0x100000
[    4.287733] scm_call failed with error code -2
[    4.287740] QSEECOM: qseecom_check_whitelist_feature: Check whitelist with ret = -22, result = 0x1000
[    4.287744] QSEECOM: qseecom_probe: qseecom.whitelist_support = 0
[    4.288101] qfp_fuse_probe: Fuse driver base:cc878000 end:cc87f000
[    4.288378] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[    4.288383] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
[    4.439802] qcrypto fe0c0000.qcom,qcrypto: Qualcomm Crypto 5.3.0 device found @0xfe0c0000
[    4.446950] qcrypto fe0c0000.qcom,qcrypto: CE device = 0x0
[    4.446950] , IO base, CE = 0xcc880000
[    4.446950] , Consumer (IN) PIPE 0,    Producer (OUT) PIPE 1
[    4.446950] IO base BAM = 0x  (null)
[    4.446950] BAM IRQ 141
[    4.446950] Engines Availability = 0x1e0111df
[    4.472501] sps:BAM 0xfe0c4000 is registered.
[    4.476734] sps:BAM 0xfe0c4000 (va:0xcc8b0000) enabled: ver:0x24, number of pipes:16
[    4.484801] QCE50: qce_sps_init:  Qualcomm MSM CE-BAM at 0x00000000fe0c4000 irq 141
[    4.495388] bus_scale_table is NULL
[    4.498035] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ecb-aes
[    4.503494] qcrypto fe0c0000.qcom,qcrypto: qcrypto-cbc-aes
[    4.508925] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ctr-aes
[    4.514352] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ecb-des
[    4.519847] qcrypto fe0c0000.qcom,qcrypto: qcrypto-cbc-des
[    4.525289] qcrypto fe0c0000.qcom,qcrypto: qcrypto-ecb-3des
[    4.530903] qcrypto fe0c0000.qcom,qcrypto: qcrypto-cbc-3des
[    4.536398] qcrypto fe0c0000.qcom,qcrypto: qcrypto-xts-aes
[    4.541943] qcrypto fe0c0000.qcom,qcrypto: qcrypto-sha1
[    4.547107] qcrypto fe0c0000.qcom,qcrypto: qcrypto-sha256
[    4.552504] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
[    4.559289] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-des
[    4.566005] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
[    4.572925] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-aes
[    4.579663] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-des
[    4.586404] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha1-cbc-3des
[    4.593291] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
[    4.600237] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-des
[    4.607150] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
[    4.614204] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-aes
[    4.621154] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-des
[    4.628104] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aead-hmac-sha256-cbc-3des
[    4.635104] qcrypto fe0c0000.qcom,qcrypto: qcrypto-hmac-sha1
[    4.640772] qcrypto fe0c0000.qcom,qcrypto: qcrypto-hmac-sha256
[    4.646561] qcrypto fe0c0000.qcom,qcrypto: qcrypto-aes-ccm
[    4.652054] qcrypto fe0c0000.qcom,qcrypto: qcrypto-rfc4309-aes-ccm
[    4.658101] qcrypto: FIPS140-2 Known Answer Tests: Skipped
[    4.663658] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[    4.672261] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
[    4.683901] qcrypto fe0c0000.qcom,qcrypto1: Qualcomm Crypto 5.3.0 device found @0xfe0c0000
[    4.691163] qcrypto fe0c0000.qcom,qcrypto1: CE device = 0x10
[    4.691163] , IO base, CE = 0xcc8c0000
[    4.691163] , Consumer (IN) PIPE 6,    Producer (OUT) PIPE 7
[    4.691163] IO base BAM = 0x  (null)
[    4.691163] BAM IRQ 141
[    4.691163] Engines Availability = 0x1e0111df
[    4.717364] QCE50: qce_sps_init:  Qualcomm MSM CE-BAM at 0x00000000fe0c4000 irq 141
[    4.727462] bus_scale_table is NULL
[    4.729910] qcrypto: FIPS140-2 Known Answer Tests: Skipped
[    4.735481] QCE50: __qce_get_device_tree_data: BAM Apps EE is not defined, setting to default 1
[    4.744116] QCE50: __qce_get_device_tree_data: CE operating frequency is not defined, setting to default 100MHZ
[    4.755049] qcrypto fe0c0000.qcom,qcrypto2: Qualcomm Crypto 5.3.0 device found @0xfe0c0000
[    4.762422] qcrypto fe0c0000.qcom,qcrypto2: CE device = 0x20
[    4.762422] , IO base, CE = 0xcc900000
[    4.762422] , Consumer (IN) PIPE 8,    Producer (OUT) PIPE 9
[    4.762422] IO base BAM = 0x  (null)
[    4.762422] BAM IRQ 141
[    4.762422] Engines Availability = 0x1e0111df
[    4.788621] QCE50: qce_sps_init:  Qualcomm MSM CE-BAM at 0x00000000fe0c4000 irq 141
[    4.798711] bus_scale_table is NULL
[    4.801159] qcrypto: FIPS140-2 Known Answer Tests: Skipped
[    4.808263] tun: Universal TUN/TAP device driver, 1.6
[    4.812274] tun: (C) 1999-2004 Max Krasnyansky 
[    4.818710] PPP generic driver version 2.4.2
[    4.823891] FIFO apps_ipc_data FOUND!
[    4.826549] FIFO apps_ipc_pcap FOUND!
[    4.830218] FIFO apps_hex_ipc_log NOT FOUND!
[    4.834413] FIFO apps_hex_ipc_log NOT FOUND!
[    4.841444] msm_sharedmem: sharedmem_register_qmi: Creating sharedmem_qmi qmi handle failed
[    4.841685] msm_sharedmem: msm_sharedmem_probe: Device created for client 'rmtfs'
[    4.857282] msm-dwc3 f9200000.ssusb: bus scaling is disabled
[    4.863647] i2c /dev entries driver
[    4.868319] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    4.875718] device-mapper: req-crypt: dm-req-crypt successfully initalized.
[    4.875718] 
[    4.884275] cpuidle: using governor ladder
[    4.888239] cpuidle: using governor menu
[    4.892161] sdhci: Secure Digital Host Controller Interface driver
[    4.898337] sdhci: Copyright(c) Pierre Ossman
[    4.902626] sdhci-pltfm: SDHCI platform and OF driver helper
[    4.908415] sdhci_msm f9824900.sdhci: sdhci_msm_probe: ICE device is not enabled
[    4.915746] sdhci_msm f9824900.sdhci: Parsing Pinctrl failed with -22, falling back on GPIO lib
[    4.924564] sdhci_msm f9824900.sdhci: host_use_default_qos = 1
[    4.930181] sdhci_msm f9824900.sdhci: For qos_policy(default qos) = 0, tbl_sz = 1, qos type = 2
[    4.938847] sdhci_msm f9824900.sdhci: 	dma_latency = 200
[    4.944125] sdhci_msm f9824900.sdhci: For qos_policy(modified dynamic qos) = 1, tbl_sz = 1, qos type = 2
[    4.953642] sdhci_msm f9824900.sdhci: 	dma_latency = 200
[    4.958910] sdhci_msm f9824900.sdhci: For qos_policy(modified dynamic qos) = 2, tbl_sz = 1, qos type = 2
[    4.968367] sdhci_msm f9824900.sdhci: 	dma_latency = 200
[    4.973639] sdhci_msm f9824900.sdhci: Host using default pm_qos
[    4.980312] mmc0: no vqmmc regulator found
[    4.983620] mmc0: no vmmc regulator found
[    4.987838] mmc0: SDHCI controller on f9824900.sdhci [f9824900.sdhci] using 32-bit ADMA in legacy mode
[    5.025318] ssbi f9b18000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
[    5.032273] ssbi f9b1c000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
[    5.039109] ssbi f9b20000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
[    5.046256] ssbi f9b24000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
[    5.053526] ssbi f9b28000.qcom,ssbi: SSBI controller type: 'geni-ssbi-arbiter'
[    5.060940] usbcore: registered new interface driver usbhid
[    5.065873] usbhid: USB HID core driver
[    5.070447] u32 classifier
[    5.072543] ipip: IPv4 over IPv4 tunneling driver
[    5.073184] mmc0: BKOPS_EN bit = 0
[    5.073191] mmc0: eMMC FW version: 0x01
[    5.080718] mmc0: new HS200 MMC card at address 0001
[    5.089319] mmcblk0: mmc0:0001 004GA0 3.68 GiB 
[    5.089884] TCP: cubic registered
[    5.089888] Initializing XFRM netlink socket
[    5.090630] NET: Registered protocol family 10
[    5.091800] NET: Registered protocol family 17
[    5.091826] NET: Registered protocol family 15
[    5.091932] Bridge firewalling registered
[    5.091999] 8021q: 802.1Q VLAN Support v1.8
[    5.094209] sctp: Hash tables configured (established 65536 bind 65536)
[    5.094999] NET: Registered protocol family 27
[    5.134066] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB
[    5.134355] Registering SWP/SWPB emulation handler
[    5.135844] regulator-dummy: disabling
[    5.137172] qcom,cc-debug-fsm9010 fc400000.qcom,cc-debug: Registered Debug Mux successfully
[    5.137506] android_probe: pm_qos latency not specified 0
[    5.137843] file system registered
[    5.137927] mbim_init: initialize 1 instances
[    5.138060] mbim_init: Initialized 1 ports
[    5.138063] mbim_bam_setup: no_ports:1
[    5.177342] mbim_bam_setup: Initialized 1 ports
[    5.183358] rndis_qc_init: initialize rndis QC instance
[    5.183488]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30 p31 p32
[    5.200815] android_usb gadget: Mass Storage Function, version: 2009/09/11
[    5.206990] android_usb gadget: Number of LUNs=1
[    5.211619]  lun0: LUN: removable file: (no medium)
[    5.216901] android_usb gadget: android_usb ready
[    5.221355] /home/user/jenkins/workspace/QualcommBspArtifact/build_90xx/LINUX/opensource/kernel/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    5.234750] msm_thermal:interrupt_mode_init Interrupt mode init
[    5.241137] clock_late_init: Removing enables held for handed-off clo...#lost UART synchronization
[    5.248286] Freeing unused kernel memory: 212K (c0734000 - c0769000)
starting pid 218, tty '': '/etc/init.d/rcS'
rcS:::executing /etc/init.d/rcS script
rcS:::mounting filesystems
rcS:::generating ld.so.cache
rcS:::executing /etc/rc.d scripts
starting udev
creating static nodes
starting udevd...[    5.356291] udevd[235]: starting version 182
done
waiting for devices...done
[    5.844461] mountflash:::Mounting /dev/disk/by-partlabel/modem_1 on /mnt/firmware
[    5.866557] mountflash:::Mounting /dev/disk/by-partlabel/rfcal on /mnt/rfcal
[    5.886640] EXT4-fs (mmcblk0p6): recovery complete
[    5.891280] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[    5.903855] mountflash:::Mounting /dev/disk/by-partlabel/system_1 on /opt
[    5.917127] EXT4-fs (mmcblk0p30): mounted filesystem with ordered data mode. Opts: (null)
[    5.929787] mountflash:::Mounting /dev/disk/by-partlabel/userdata on /mnt/flash
[    5.948306] EXT4-fs (mmcblk0p14): recovery complete
[    5.952947] EXT4-fs (mmcblk0p14): mounted filesystem with ordered data mode. Opts: (null)
[    5.975236] mountflash:::Mounting /dev/disk/by-partlabel/stack_1 on /stack
[    5.991878] EXT4-fs (mmcblk0p31): recovery complete
[    5.996640] EXT4-fs (mmcblk0p31): mounted filesystem with ordered data mode. Opts: (null)
[    6.009011] mountflash:::Mounting /dev/disk/by-partlabel/config_1 on /config
[    6.032287] EXT4-fs (mmcblk0p32): recovery complete
[    6.036924] EXT4-fs (mmcblk0p32): mounted filesystem with ordered data mode. Opts: (null)
[    6.056885] mountflash:::generating ld.so.cache
/etc/rc.d/S02persist-fixup: fixing up persistent files
/etc/rc.d/S02persist-fixup: fixed up entry /root
/etc/rc.d/S02persist-fixup: fixed up entry /home
/etc/rc.d/S02persist-fixup: fixed up entry /etc/dropbear/dropbear_dss_host_key
/etc/rc.d/S02persist-fixup: fixed up entry /etc/dropbear/dropbear_rsa_host_key
/etc/rc.d/S02persist-fixup: fixed up entry /etc/rsyslog.conf
/etc/rc.d/S02persist-fixup: done fixing up persistent files
running rc.once.d services...
Creating dynamic linker cache...
syslogd starting
klogd starting
boardinit:::Loading NSS GMAC ethernet module
[    6.418000] libphy: GPIO Bitbanged MDIO: probed
[    6.442553] **********************************************************
[    6.448099] * Driver    :NSS GMAC Driver for RTL v(3.72a)
[    6.453428] * Version   :1.0
[    6.456290] * Copyright :Copyright (c) 2013-2016 The Linux Foundation. All rights reserved.
[    6.464661] **********************************************************
[    6.471875] GMAC0(c251b500) Invalid MAC@ - using 72:73:74:75:76:77
[    6.482627] GMAC1(c2518500) Invalid MAC@ - using be:bf:c0:c1:c2:c3
boardinit:::Setting up coredump location in /mnt/flash
boardinit:::Creating /dev/mqueue
fs.mqueue.msg_max = 256
starting dropbear...done
Setting up LVM2...
  No volume groups found
done
Using stack init scripts to configure networking.
stop syslogd stopping syslog
/etc/rc.d/S84rsyslogd: line 70:   402 Terminated              /etc/init.d/syslogd stop

Starting system logger (rsyslogd): 
Starting OAM Proxy (/opt/qcom/bin/fsmOamProxy): 
Starting (/opt/qcom/bin/fsmPhyTraceProxy): 
loading modules
/etc/rc.d/S99persist-save: saving persistent files
/etc/rc.d/S99persist-save: done saving persistent files
rcS:::configuring ACPU parameters
rcS::Starting fsminitd
Starting (/local/qcom/bin/fsminit/fsminitd): 
rcS::fsminitd started
rcS:::Running /stack/etc/rc.once.d scripts
[    7.094340] /etc/init.d/sentinel ::: Started ...
[    7.098899] /etc/init.d/sentinel ::: Checking partitions ...
[    7.134130] /etc/init.d/sentinel ::: Waiting 1200 seconds to stack boot up ...
rcS:::Running /stack/etc/rc.d scripts
[    7.246477] warning: `fsmPhyTraceProx' uses 32-bit capabilities (legacy support in use)
Waiting for fsminitd (reattemp 1)...
Waiting for fsminitd (reattemp 2)...
[   11.306417] pil-femto-modem fbc00000.qcom,modem-femto: mba: loading from 0x13080000 to 0x130da000
[   11.381625] pil-femto-modem fbc00000.qcom,modem-femto: MBA boot done
[   11.386958] pil-femto-modem fbc00000.qcom,modem-femto: mba: Brought out of reset
[   11.394629] pil-femto-modem-desc fd4a7000.qcom,modem: mdm0_00: loading from 0x16400000 to 0x17848000
[   11.587178] pil-femto-modem-desc fd4a7000.qcom,modem: mdm0_00: Brought out of reset
[   11.594050] pil-femto-modem-desc fd4a7030.qcom,modem: mdm1_00: loading from 0x18000000 to 0xfb840000
[   12.156569] pil-femto-modem-desc fd4a7030.qcom,modem: mdm1_00: Brought out of reset
[   12.163410] pil-femto-modem-desc fd4a7060.qcom,modem: mdm2_00: loading from 0x00800000 to 0xf7998000
[   12.324944] pil-femto-modem-desc fd4a7060.qcom,modem: mdm2_00: Brought out of reset
[   12.331760] pil-femto-modem-desc fd4a7090.qcom,modem: mdm3_00: loading from 0x14000000 to 0x140a1000
[   12.359027] pil-femto-modem-desc fd4a7090.qcom,modem: mdm3_00: Brought out of reset
[   12.396326] smsm_change_state 
[   12.400884] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c086b878
[   12.486398] smsm_change_state 
Waiting for fsminitd (reattemp 3)...
[   12.656033] Synchronized with fsminitd
[   12.929833] incorrect memory info c1005d8c len 16
[   12.948994] :module loaded (platform - IPQ806x, build - Build_ID - 04/09/21, 11:18:21)
[   12.957576] :Register with NSS driver-
Shutting down system logger (rsyslogd): [   12.981371] crypto bench loaded - Build_ID - 04/09/21, 11:18:21
stopped /usr/sbin/rsyslogd (pid 408)

[   13.009037] nss_ipsecmgr_init[1362]:NSS IPsec manager loaded: Build Id: 04/09/21, 11:18:21
[   13.027538] nss_nl_init[296]:NSS Netlink manager loaded: Build Id: 04/09/21, 11:18:21
[   13.034333] nss_nl_init[314]:attaching family:nss_nlcrypto
[   13.039917] nss_nlcrypto_init[598]:initiallizing the NSS netlink crypto handler
[   13.047116] nss_nl_init[314]:attaching family:nss_nlipv4
[   13.052411] nss_nlipv4_init[793]:Init NSS netlink IPv4 handler
[   13.057217] :NSS Firmware initialized
[   13.057439] :probing engine - 0
[   13.057442] :Device Tree node found
[   13.057565] :init completed for Pipe Pair[0]
[   13.057581] :init completed for Pipe Pair[1]
[   13.082212] nss_nl_init[314]:attaching family:nss_nlipsec
[   13.087566] nss_nlipsec_init[1150]:Init NSS netlink IPsec handler
[   13.093647] nss_nl_init[314]:attaching family:nss_nloam
[   13.098869] nss_nl_init[314]:attaching family:nss_nlipv6
[   13.104124] nss_nlipv6_init[777]:Init NSS netlink IPV6 handler
[   13.971344] :probing engine - 1
[   13.974491] :Device Tree node found
[   13.979099] :init completed for Pipe Pair[0]
[   13.984324] :init completed for Pipe Pair[1]
Starting system logger (rsyslogd): 
/stack/etc/rc.d/S01stackenv: line 181: /sys/kernel/debug/tracing/tracing_on: No such file or directory
[   14.302169] Configuring board type: 9016, RF id: 51
[   14.333800] hex2_shm: registered correctly with major number 243
[   14.338886] hex2_shm: device class registered correctly
[   14.344216] hex2_shm: device class created correctly
[   14.357272] casa_gpio: Initializing
[   14.360008] casa_gpio: Valid GPIO in device tree (red_led-gpio,1002)
[   14.366084] casa_gpio: Valid GPIO in device tree (green_led-gpio,954)
[   14.372773] casa_gpio: Valid GPIO in device tree (blue_led-gpio,956)
[   14.378918] casa_gpio: GPIO not found in device tree (orange_led-gpio)
[   14.387285] casa_gpio: Valid GPIO in device tree (reset_button-gpio,955)
[   14.393286] casa_gpio: GPIO not found in device tree (killswitch_button-gpio)
[   14.400326] casa_gpio: Valid GPIO in device tree (wifireset_control-gpio,958)
[   14.407501] casa_gpio: Valid GPIO in device tree (wifiwps_control-gpio,959)
[   14.712127] health_monitor started
[   15.024529] smsm_change_state 
[   15.064275] oam_proxy started
[   16.679016] system_layer: ==================================================================
[   16.687468] system_layer: System layer
[   16.691102] system_layer: Casa Systems Inc. © 2008-2020 All Rights Reserved
[   16.701044] system_layer: Sofware version: 4.8.26
[   16.705687] system_layer: Serial number: A01A19002135
[   16.710703] system_layer: ==================================================================
[   16.856661] system_layer: [OAM] Component registration complete
[   16.873160] system_layer: [OAM] Subscribed to event: no_ues_connected
[   16.888179] system_layer: [OAM] Subscribed to event: ues_connected
[   16.903057] system_layer: [OAM] Subscribed to event: location_acquired
[   16.917876] system_layer: [OAM] Subscribed to event: waiting_for_wifi_configuration
[   16.933864] system_layer: [OAM] Subscribed to event: booting
[   16.947708] system_layer: [OAM] Subscribed to event: admin_mode_enabled
[   16.963038] system_layer: [OAM] Subscribed to event: enb_online
[   16.977077] system_layer: [OAM] Subscribed to event: acquiring_backhaul
[   16.992138] system_layer: [OAM] Subscribed to event: acquiring_location
[   17.007411] system_layer: [OAM] Subscribed to event: critical_alarm_raised
[   17.022848] system_layer: [OAM] Subscribed to event: factory_reset
[   17.037061] system_layer: [OAM] Subscribed to event: disabling_admin_mode
[   17.052200] system_layer: [OAM] Subscribed to event: backhaul_acquired
[   17.149268] system_layer: Starting WiFi module
[   37.957125] qup_i2c f9924000.i2c: QUP: I2C status flags :0x1363c8, irq:129
[   37.963035] qup_i2c f9924000.i2c: I2C slave addr:0x54 not connected
[   39.194935] qup_i2c f9924000.i2c: QUP: I2C status flags :0x1363c8, irq:129
[   39.200918] qup_i2c f9924000.i2c: I2C slave addr:0x54 not connected
[   53.883791] system_layer: Wifi module boot up completed.
[   54.054148] system_layer: WiFi Module Banner:
[   54.054148]   _______                     ________        __
[   54.054148]  |       |.-----.-----.-----.|  |  |  |.----.|  |_
[   54.054148]  |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
[   54.054148]  |_______||   __|_____|__|__||________||__|  |____|
[   54.054148]           |__| W I R E L E S S   F R E E D O M
[   54.054148]  -----------------------------------------------------
[   54.054148]  BARRIER BREAKER (Barrier Breaker, r15)
[   54.054148]  -----------------------------------------------------
[   54.054148]   * 1/2 oz Galliano         Pour all ingredients into
[   54.054148]   * 4 oz cold Coffee        an irish coffee mug filled
[   54.054148]   * 1 1/2 oz Dark Rum       with crushed ice. Stir.
[   54.054148]   * 2 tsp. Creme de Cacao
[   54.054148]  -----------------------------------------------------
[   54.054148]  MTK OpenWrt SDK V3.4
[   54.054148]  revision : 1443366e
[   54.054148]  benchmark : APSoC SDK 5.0.1.0
[   54.178731] system_layer: WiFi Module Uptime : 
[   54.178731]  21:59:36 up 0 min,  load average: 1.12, 0.29, 0.10
[   54.178731] 
[   54.228441] system_layer: WiFi Module Version : 
[   54.228441] MOWIFI CX2 V1.0
[   54.228441] 1.0.1 Build 20190508 Rel.15n
[   54.228441] G24=1 G5=1
[   54.228441] 
[   54.258718] system_layer: Configuring WiFi DHCP...
[   56.128821] system_layer: WiFi DHCP configured
[   56.142590] system_layer: [OAM] Subscribed to event: enabling_admin_mode
[   56.157631] system_layer: [OAM] Subscribed to event: admin_mode_enabled
[   56.172926] system_layer: [OAM] Subscribed to event: disabling_admin_mode
[   56.188017] system_layer: [OAM] Subscribed to event: enb_online
[   56.213553] system_layer: [OAM] Subscribed to event: forced_reboot
[   56.228578] system_layer: [OAM] Subscribed to event: acquiring_location
[   56.243587] system_layer: [OAM] Subscribed to event: location_acquired
[   56.258324] system_layer: [OAM] Subscribed to event: failure_acquiring_location
[   56.273684] system_layer: [OAM] Subscribed to event: critical_alarm_raised
[   56.289293] system_layer: [OAM] Subscribed to event: critical_alarm_cleared
[   56.413875] system_layer: [OAM] Subscribed to event: location_acquired
[   56.423937] system_layer: Configured device_time zone to PST8PDT
[   56.442791] system_layer: [OAM] Subscribed to event: backhaul_acquired
[   57.841680] system_layer: Interface eth0 MAC address set to 00:17:10:26:E3:EC
[   57.881982] system_layer: Interface eth1 MAC address set to 02:17:10:26:E3:EC
[   57.890312] system_layer: Preferred Backhaul Mode: ethernet
[   57.896074] system_layer: Preferred Backhaul Ethernet
[   57.901076] system_layer: Configuring Ethernet Backhaul
[   57.938216] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   68.003229] system_layer: Failure configuring Ethernet Backhaul
[   68.009258] system_layer: Interface eth0 state did not change to up: Condition not meet after 10 seconds with interval 0.1
[   68.020473] system_layer: Configuring WiFi Backhaul
[   68.025303] system_layer: Enabling WiFi STA
[   90.708300] system_layer: Checking WiFi connection, attempt 0.
[   95.803932] system_layer: Checking WiFi connection, attempt 1.
[  100.906704] system_layer: Checking WiFi connection, attempt 2.
[  106.002518] system_layer: Checking WiFi connection, attempt 3.
[  111.098262] system_layer: Checking WiFi connection, attempt 4.
[  116.193829] system_layer: Checking WiFi connection, attempt 5.
[  121.289480] system_layer: Checking WiFi connection, attempt 6.
[  126.384992] system_layer: Checking WiFi connection, attempt 7.
[  131.498737] system_layer: Failure configuring WiFi Backhaul
[  131.504302] system_layer: Max retries reached trying to connect to Band 5g, SSID ***REDACTED***
[  131.512423] system_layer: Configuring WiFi AP. SSID: Sprint-Pebble
[  131.518674] system_layer: Configuring WiFi...
[  163.218677] system_layer: WiFi configured as AP
[  163.287590] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[  166.489544] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[  166.501406] eth1: 1000 Mbps Full Duplex
[  166.514230] system_layer: eth1: Using DHCP...
[  179.269404] BACKHAUL_INTERFACE = , interface = eth1, ip = 192.168.51.2
[  179.275281] Setting hostname to pebble
[  179.282525] system_layer: eth1 IP set by DHCP
[  179.284043] eth1: deleting routers
[  179.294441] eth1: Deleting dns from /etc/resolv.conf
[  179.304234] eth1: adding dns 192.168.51.1
[  179.387627] system_layer: Started PTP client
[  179.433644] system_layer: [OAM] Subscribed to event: layer_not_running
[  179.441245] system_layer: System layer started
[  179.446706] system_layer: Creating Sentinel Mark /tmp/watchdog_alive
[  179.977949] ftrm started
[  180.019482] locmgr started
[  180.062380] nl started
[  180.104295] nlSyncApp started
[  180.258944] Waiting for NSS driver...
[  180.268838] syncmgr started using GNSS as primary source
Accepting OAM request from command line...
RecordID: 0x15010005
RequestType: Set
RequestOpType: Update
RequestData:


  
  

Result: Success
Apply Action: no-action-required

Accepting OAM request from command line...
RecordID: 0x15010005
RequestType: Set
RequestOpType: Update
RequestData:


  
  

Result: Success
Apply Action: no-action-required

[  182.468692] Cleaning residual values on configuration database
[  183.028910] upnp started
[  183.965494] Waiting for GPS synchronization...
  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
  0     0    0     0    0     0      0      0 --:--:-- --:--:-- --:--:--     0100    26    0     0  100    26      0   9454 --:--:-- --:--:-- --:--:-- 13000






^Nle[ 1683.854567] WARNING: GPS synchronization failed!
[ 1689.117649] system_layer: NTP synchronization with server pool.ntp.org failed
{"cause": "NTP Synchronization failed"}[ 1689.666841] Regenerating vendor key.der
writing RSA key
00[APP] Encrypted key written to /tmp/key.bin
00[APP] /mnt/flash/persist/root/.vendor/private/key.der successfully encrypted!
00[APP] Key from /tmp/key.bin successfully provisioned!
Certificate will not expire
Certificate will not expire
[ 1689.877717] Main SeGW FQDN set to segw-sc-global.spcsdns.net
[ 1689.882616] Generating connection conf: 192.168.51.2 ==> segw-sc-global.spcsdns.net
cp: can't stat '/mnt/flash/persist/root/.vendor/cacerts//*': No such file or directory
Stopping strongSwan IPsec...
Starting strongSwan 5.3.5 IPsec [starter]...
modprobe: module ah4 not found in modules.dep
modprobe: module esp4 not found in modules.dep
modprobe: module ipcomp not found in modules.dep
modprobe: module xfrm4_tunnel not found in modules.dep
modprobe: module xfrm_user not found in modules.dep
Waiting for ipsec... #Repeats a whole bunch of times
Waiting for ipsec...
[ 1814.910621] Restarting system.
[ 1814.912666] Going down for restart now
[ 1814.916633] Failed to disable secure wdog debug: -4
[ 1814.921378] Calling SCM to disable SPMI PMIC arbiter

and then it reboots to the bootloader.