Alarm.com VVTK8112 WiFi Puck Camera Serial Console
Written 2021-07-25
Tags:vivotek alarm.com
My house came with a partially working security system, including a WiFi camera with 256MB RAM, 128MB SPI Flash,
There's a Vivotek ARM9 chip with a serial port inside at 38400 baud, on J6, which is on the lower-left of the photo below and I'm not sure but looks like a 4 pin JST mini connector. Pin4 is ground, Pin3 is TX from the device. I did not try to talk to it, but RX should be pins 1 or 2.
Here's what it said to me:
U-Boot 2009.06-2.0.6-svn186232 (May 05 2016 - 13:24:05)
=== U-Boot DDR Reserved Area ===
!! Please do not write any data to these locations. !!
TEXT section : 0x00002000 -> 0x0001ee38
BSS section : 0x0001ee38 -> 0x00020afc
MALLOC Area : 0x00020afc -> 0x00320afc
STACK : 0x00320b7c -> 0x0036bb88
GMAC Desc/Buf : 0x0036bba0 -> 0x00377da0
=== DRAM Configuration ===
Bank #0 : 0x00000000 256 MB
=== GPIO Configuration ===
=== NAND Configuration ===
SPIFLASH: Got idcode ff c8 21 7f 7f
SF: Detected PSU1GS20BN with page size 2048, total 128 MB
Flash Type : SPI NAND Flash Chip.
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Chip Size : 128 MiB
=== Boot Configuration ===
Boot Storage : Serial NAND Flash
Finding the environment variables in boot storage...
*** Warning - bad CRC or NAND, using default environment
=== Model Name ===
Model Name : VVTK8112
=== Loader Info ===
Loader Version# : 0x15050701 (This value is stored at 0x41001000)
Boot from = SN
Hit hotkey: b, d, n, u
Flash status = 255
NAND Reading : #
NAND Reading : ##############ECC corrected = 1
###
2186856 bytes read: OK
Image Name: linux-3.10.49
Created: 2017-04-13 8:19:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2186792 Bytes = 2.1 MB
Load Address: 00408000
Entry Point: 00408000
Verifying Checksum ... OK
NAND Reading : #
NAND Reading : #
6389 bytes read: OK
Image Name: linux-3.10.49
Created: 2015-11-09 6:26:37 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6325 Bytes = 6.2 kB
Load Address: 00408000
Entry Point: 00408000
Verifying Checksum ... OK
NAND Reading : #
NAND Reading : ####################################ECC corrected = 1
########################################ECC corrected = 1
####################
12525632 bytes read: OK
Image Name: Rootfs
Created: 2017-04-13 8:24:35 UTC
Image Type: ARM Linux Filesystem Image (uncompressed)
Data Size: 12525568 Bytes = 11.9 MB
Load Address: 02ffffc0
Entry Point: 03000000
Verifying Checksum ... OK
## Booting Linux kernel at 0x00a00040 ...
Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.49 (hayes.hsu@rd1-3) (gcc version 4.9.1 (Buildroot 2014.08) ) #13 PREEMPT Thu Apr 13 16:19:34 CST 2017
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: VATICS Pesaro SoC (Flattened Device Tree), model: Pesaro SoC
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 34544
Kernel command line: root=/dev/ram0 ro initrd=0x3000000,32M ramdisk_size=32000 mem=136M console=2,38400 user_debug=31 phy_mode=mii
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 136MB = 136MB total
Memory: 99068k/99068k available, 40196k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc9000000 - 0xff000000 ( 864 MB)
lowmem : 0xc0000000 - 0xc8800000 ( 136 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0563a44 (5487 kB)
.init : 0xc0564000 - 0xc05859c4 ( 135 kB)
.data : 0xc0586000 - 0xc05bf310 ( 229 kB)
.bss : 0xc05bf310 - 0xc05e1338 ( 137 kB)
Preemptible hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
SYSC counter at clock 12000000
TMRC at APB bus clock 100000000
vpl_sys_timer_init virq 16
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
Console: colour dummy device 80x30
Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc0406620 - 0xc040665c
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
lm device registered, virq: 33!
bio: create slab at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Initialized.
Switching to clocksource sysc_freerun_counter
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (junk in compressed archive); looks like an initrd
Freeing initrd memory: 32768K (c3000000 - c5000000)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.22)
msgmni has been set to 257
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
ab800000.serial: ttyS0 at MMIO 0xab800004 (irq = 18) is a 16550A
ac000000.serial: ttyS1 at MMIO 0xac000004 (irq = 19) is a 16550A
ac800000.serial: ttyS2 at MMIO 0xac800004 (irq = 20) is a 16550A
console [ttyS2] enabled
ad000000.serial: ttyS3 at MMIO 0xad000004 (irq = 21) is a 16550A
brd: module loaded
GPIO Device Driver version 1.0.0.1
dws->irq 17, get 17
dws->max_freq 100000000
dw_spi_mmio a0800000.spi: master is unqueued, this is deprecated
id: c8 21
NAND device: Manufacturer ID: 0xc8, Chip ID: 0x21 (Unknown Mira PSU1GS20 1G 3.3V SPI), 128MiB, page size: 2048, OOB size: 64
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
5 ofpart partitions found on MTD device spi0.0
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000008000000 : "Boot"
0x000002d00000-0x000004d00000 : "Rootfs"
0x000004d00000-0x000005500000 : "Flashfs-1"
0x000005500000-0x000007e00000 : "Flashfs-2"
0x000007e00000-0x000008000000 : "NFDI"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
GMAC: PHY mode is mii
stmmac - user ID: 0x10, Synopsys ID: 0x40
DMA HW capability register supported
RX Checksum Offload Engine supported
TX Checksum insertion supported
clk rate 200000000
eth0 - (dev. name: 90000000.dw_eqos - id: -1, IRQ #0
IO base addr: 0xc910c000)
libphy: dweqos_mdio: probed
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver usb-storage
rtc-s35390a 0-0030: error resetting chip
rtc-s35390a: probe of 0-0030 failed with error -5
i2c /dev entries driver
vpl_wdt ad800000.vpl_wdt: VPL Watchdog Timer Hardware Rev 0x01020000
vpl_wdt ad800000.vpl_wdt: Driver Version 1.0.0.0: initial timeout 60 sec, nowayout=1
Synopsys Designware Multimedia Card Interface Driver
dwmmc_pesaro 92000000.dwmmc0: dev-id: 0
dwmmc_pesaro 92000000.dwmmc0: Using internal DMA controller.
dwmmc_pesaro 92000000.dwmmc0: Version ID is 270a
dwmmc_pesaro 92000000.dwmmc0: DW MMC controller at irq 25, 32 bit host data width, 16 deep fifo
dwmmc_pesaro 92000000.dwmmc0: 1 slots initialized
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
/home/vivotek/lsp/rossini/kernel_platform/kernel/pesaro_kernel_3.10_r50403-r50221/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: squashfs filesystem found at block 0
RAMDISK: Loading 12232KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (squashfs filesystem) readonly on device 1:0.
Freeing unused kernel memory: 132K (c0564000 - c0585000)
init started: BusyBox v1.22.1 (2017-04-13 16:20:08 CST)
UBI: attaching mtd2 to ubi0
UBI: scanning is finished
UBI: attached mtd2 (name "Flashfs-1", size 8 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 245/145, WL threshold: 4096, image sequence number: 134069212
UBI: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 20
UBI: background thread "ubi_bgt0d" started, PID 72
UBI device number 0, total 64 LEUBI: attaching mtd3 to ubi1
Bs (8126464 bytes, 7.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
UBI: scanning is finished
UBI: attached mtd3 (name "Flashfs-2", size 41 MiB) to ubi1
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 328, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 50/29, WL threshold: 4096, image sequence number: 1431253369
UBI: available PEBs: 0, total reserved PEBs: 328, PEBs reserved for bad PEB handling: 20
UBI: background thread "ubi_bgt1d" started, PID 76
UBI device number 1, total 328 LEBs (41648128 bytes, 39.7 MiB), UBIFS: background thread "ubifs_bgt0_0" started, PID 79
available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "flashfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 3809280 bytes (3 MiB, 30 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
UBIFS: reserved for root: 179921 bytes (175 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 14966A3A-210E-4496-8B7F-B4CD7ECAE98B, small LPT model
UBIFS: background thread "ubifs_bgt1_0" started, PID 82
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 1, volume 0, name "flashfs2"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 37330944 bytes (35 MiB, 294 LEBs), journal size 1904640 bytes (1 MiB, 15 LEBs)
UBIFS: reserved for root: 1763232 bytes (1721 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 1682BFE5-2F31-4E62-86CA-8864A163DC97, small LPT model
/etc exist
Build fifo for media
kernel.msgmnb = 65536
vm.dirty_ratio = 1
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 4096
vm.vfs_cache_pressure = 163
vm.panic_on_oom = 2
kernel.panic = 1
.sys.module.cifs.parameters.enable_oplocks = 0
check apply_patch_before
run-parts -a start /etc/rcS.d
"dpc" is not exist!
"dpc" read fail!
Read DPC table fail!
VPL_EDMC: initialized (driver 6.1.0.5 HW 14.6.0.2) Oct 12 2015 20:12:28
DRAM 0 base address = 0x08800000, size = 0x07800000
Install VPL_DMAC device driver version 1.0.0.0 on VPL_DMAC hardware version 2.1.0.0 complete !!
Install VMA_JEBE device driver version 1.0.0.1 on VMA_JEBE hardware version 1.4.0.23 complete !!
Install VMA_H4CDE device driver version 2.0.0.7 on VMA_H4EE hardware version 16.1.0.43 complete !!
Install VMA_ISPE device driver version 7.0.0.0 on VMA_ISPE hardware version 4.7.0.3 complete !!
Install VPL_VIC device driver version 2.0.8.12 on VPL_VIC hardware version 7.0.0.12 complete !!
[IMX225]: Device 0 insmod success.
IMX225_Init Done!
Install autoexposure driver version 7.0.0.1 complete !!
Install autowhitebalance driver version 4.0.0.0 complete !!
ICR Device Driver version 1.0.0.0
soc-audio soc-audio.0: ASoC: machine pesaro_evm should use snd_soc_register_card()
soc-audio soc-audio.0: dwc-hifi <-> vatics-pcm mapping ok
soc-audio soc-audio.0: hdmi-hifi <-> vatics-pcm mapping ok
Starting led: .
Starting restore: .
Starting configer: .
Starting shm_allocate: .
Starting vadpshmalloc: .
Starting swatchdog: .
Starting synctime: Thu Jan 1 00:00:00 UTC 2015
.
Starting chronos: .
Starting ectun: .
Starting eventmgr: Starting eventmgr with support for EcTun
.
Starting radvdump: .
.
Starting /etc/rcS.d/S14network: eth0: device MAC address 00:02:d1:47:d3:24
dweqos 90000000.dw_eqos eth0: dweqos_init_phy: trying to attach to dweqos_mdio-ffff:01
dweqos 90000000.dw_eqos eth0: dweqos_init_phy: attached to PHY (UID 0x2430c54) Link = 1
dweqos 90000000.dw_eqos eth0: PHY: ICPlus IP101A/G
.
dwc_otg: version 3.0.0.3(3.10a 21-DEC-2012)
dwc_otg lm0: USB PHY CTRL value: 0x821c06e4
dwc_otg lm0: Host only
Core Release: 3.10a
Setting default values for core params
Setting core params with module parameters
Using Buffer DMA mode
Periodic Transfer Interrupt(PTI) Enhancement - disabled
Multiprocessor Interrupt(MPI) Enhancement - disabled
OTG VER PARAM: 0, OTG VER FLAG: 0
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 33, io mem 0x00000000
Init: Power Port (0)
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Waiting for releasing memory, free memory: 93636
Indeed it is in host mode hprt0 = 00021501
usb 1-1: new high-speed USB device number 2 using dwc_otg
Indeed it is in host mode hprt0 = 00001101
Waiting for releasing memory, free memory: 93800
REALTEK_RTL8192EU
RTL871X: module init start
RTL871X: rtl8192eu v4.3.8_12406.20140929
RTL871X: build time: Jun 6 2016 16:53:44
RTL871X:
usb_endpoint_descriptor(0):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=84
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_in = 4
RTL871X:
usb_endpoint_descriptor(1):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=5
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_out = 5
RTL871X:
usb_endpoint_descriptor(2):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=6
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_out = 6
RTL871X:
usb_endpoint_descriptor(3):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=87
RTL871X: wMaxPacketSize=64
RTL871X: bInterval=3
RTL871X: RT_usb_endpoint_is_int_in = 7, Interval = 3
RTL871X:
usb_endpoint_descriptor(4):
RTL871X: bLength=7
RTL871X: bDescriptorType=5
RTL871X: bEndpointAddress=8
RTL871X: wMaxPacketSize=512
RTL871X: bInterval=0
RTL871X: RT_usb_endpoint_is_bulk_out = 8
RTL871X: nr_endpoint=5, in_num=2, out_num=3
RTL871X: USB_SPEED_HIGH
RTL871X: CHIP TYPE: RTL8192E
RTL871X: register rtw_netdev_ops to netdev_ops
RTL871X: ReadChipVersion192e 0xF0 = 0xc441135
RTL871X: Chip Version Info: CHIP_8192E_Normal_Chip_SMIC_B_CUT_2T2R_RomVer(0)
RTL871X: RF_Type is 2!!
RTL871X: _ConfigChipOutEP_8192E OutEpQueueSel(0x07), OutEpNumber(3)
RTL871X: ====> ReadAdapterInfo8192EU
RTL871X: Boot from EFUSE, Autoload OK !
RTL871X: EEPROM ID=0x8129
RTL871X: VID = 0x0BDA, PID = 0x818B
RTL871X: Customer ID: 0x00, SubCustomer ID: 0xCD
RTL871X: hal_ReadMACAddress_8192EU MAC Address from EFUSE = 5c:f3:70:31:7e:a6
RTL871X: Hal_ReadPowerSavingMode8192E...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(1)
RTL871X: ### PS params=> power_mgnt(0),usbss_enable(0) ###
RTL871X: EEPROMRegulatory = 0x1 TxPwrCalibrateRate=0x0
RTL871X: Board Type: Dongle or WIFI only Module
RTL871X: mlmepriv.ChannelPlan = 0x22
RTL871X: CrystalCap: 0x23
RTL871X: ThermalMeter = 0x1a
RTL871X: SWAS: bHwAntDiv = 0, TRxAntDivType = ff
RTL871X: pHalData->PAType_2G is 0x0, pHalData->ExternalPA_2G = 0
RTL871X: pHalData->LNAType_2G is 0x0, pHalData->ExternalLNA_2G = 0
RTL871X: ReadAdapterInfo8192EU <====
RTL871X: Hal_ChannelPlanToRegulation ChannelPlan:0x22,Regulation(2_4G/5G):0x00,0x03
RTL871X: init_channel_set ChannelPlan ID 22 Chan num:11
RTL871X: rtw_alloc_macid(eth%d) if1, hwaddr:ff:ff:ff:ff:ff:ff macid:1
RTL871X: rtw_macaddr_cfg MAC Address = 00:02:d1:47:d3:24
RTL871X: bDriverStopped:1, bSurpriseRemoved:0, bup:0, hw_init_completed:0
RTL871X: rtw_ndev_init(wlan0)
RTL871X: _rtw_drv_register_netdev, MAC Address (if1) = 00:02:d1:47:d3:24
usbcore: registered new interface driver rtl8192eu
RTL871X: module init ret=0
RTL871X: +871x_drv - drv_open, bup=0
RTL871X: ==>_InitPowerOn_8192EU
RTL871X: SetHwReg8192E: bMacPwrCtrlOn=1
RTL871X: ===> FirmwareDownload88E() fw source from Header.
RTL871X: FirmwareDownload8192E fw:NIC, size: 31818
RTL871X: FirmwareDownload8192E: fw_ver=19 fw_subver=0 sig=0x92e1
RTL871X: polling_fwdl_chksum: Checksum report OK! (1, 0ms), REG_MCUFWDL:0x00070305
RTL871X: =====> _8051Reset8192E(): 8051 reset success .
RTL871X: _FWFreeToGo8192E: Polling FW ready OK! (82, 30ms), REG_MCUFWDL:0x000706c6
RTL871X: FWDL success. write_fw:1, 100ms
RTL871X: ===> phy_BB8192E_Config_ParaFile() EEPROMRegulatory 1
RTL871X: PHY_BBConfig8192E ==> CrystalCap:0x23
RTL871X: Auto InitLLTTable8192E success
RTL871X: pDM_Odm TxPowerTrackControl = 1
RTL871X: phy_SpurCalibration_8192E =>AFE_PHASE_SEL
RTL871X: ===FixSpur NOT Pass!
RTL871X: wlan0 MAC Address from REG_MACID = 00:02:d1:47:d3:24
RTL871X: rtl8192eu_hal_init in 1870ms
RTL871X: wlan0Port-0 set opmode = 2
RTL871X: MAC Address = 00:02:d1:47:d3:24
RTL871X: -871x_drv - drv_open, bup=1
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
RTL871X: rtw_ioctl_standard_wext_private:...
RTL871X: _rtw_ioctl_wext_private: cmd=mp_priv_ver
RTL871X: _rtw_ioctl_wext_private: parameters=
RTL871X: mp_get MP_GETVER
RTL871X: rtw_ioctl_standard_wext_private:...
RTL871X: _rtw_ioctl_wext_private: cmd=efuse_get
RTL871X: _rtw_ioctl_wext_private: parameters=rmap,b8,1
RTL871X: efuse get EFUSE_GET
RTL871X: rtw_pm_set_ips IPS_NONE
RTL871X: rtw_mp_efuse_get: in=rmap,b8,1
RTL871X: rtw_mp_efuse_get: addr=b8
RTL871X: rtw_mp_efuse_get: cnts=1
RTL871X: rtw_pm_set_ips IPS_NONE
RTL871X: (2)871x_drv - drv_close, bup=1, hw_init_completed=1
RTL871X: indicate disassoc
RTL871X: +rtl8192e_set_FwJoinBssReport_cmd(wlan0): iface_type=0 mstatus(0)
RTL871X: HW_VAR_BASIC_RATE: 0x15f -> 0x15f -> 0x15f
RTL871X: -871x_drv - drv_close, bup=1
Wait for eth0 ready!(0)
Wait for eth0 ready!(1)
Wait for eth0 ready!(2)
[S14network] Waiting for config_wireless_mode
.
.
.
.
.
RTL871X: +871x_drv - drv_open, bup=1
RTL871X: -871x_drv - drv_open, bup=1
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
RTL871X: set_mode = IW_MODE_INFRA
RTL871X: wlan0Port-0 set opmode = 2
RTL871X: set bssid:00:00:00:00:00:00
RTL871X: [rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
.
.
.
.
.
[S14network] config_wireless_mode finished
udhcpc (v1.22.1) started
Sending discover...
Sending discover...
Sending discover...
network_ipaddress=0.0.0.0
network_subnet=
network_router=
network_dns1=
network_dns2=
network_wins1=
network_wins2=
No lease, forking to background
.
* Starting ip filter with iptables...
iptables/ip6tables disabled
[ ok ]
Starting syslogd: .
Anubis architecture
router=
UPnP CP disabled
Starting adec: config file parse OK!!
Initial FIFO succeeded, fd = 3
src/audioout_alsPLL Unlock....
a.c:79:open audio-out device (0x14e7980)
snd_pcm_hw_params set period size 320
[Georgie] boundary: 1073741824
dwGainPercentage = 0, dwGain = 411
.
Starting aenc: .
Starting venc: .
Starting mod: .
sensor initial
Starting rtsps: [IMX225]: Open device 0 done
run as daemon mode
.
Starting serverpush: .
Starting httpd: .
.
https_status=1
Starting stunnel: [VIC] : open success!!
sensor no support WDR 742 root 3192 S /usr/sbin/stunnel /etc/conf.d/stunnel.conf
.
Starting recorder: .
Starting inetd: .
Starting upnpdd: .
Starting iod: .
Cannot resolve 'deviceapi.alarm.com:443' - delaying DNS lookup
Starting uartd: .
Starting vpnwatch: .
Starting ddnsc: change
ddns server name : 127.0.0.1
DDNS run as daemon coz specific service providers
Starting snapshotd: Total stream num: 4, default stream ID: -1
Entering daemon mode...
.
Starting vid: .
Starting ptzmanager:
Driver not found
.
Starting alarmaudioupstream: .
.
test network status...
killall: imgbufmgr: no process killed
RTL871X: rtw_wx_get_rts, rts_thresh=2347
RTL871X: rtw_wx_get_frag, frag_len=2346
RTL871X: rtw_wx_get_rts, rts_thresh=2347
RTL871X: rtw_wx_get_frag, frag_len=2346
RTL871X: rtw_wx_get_rts, rts_thresh=2347
RTL871X: rtw_wx_get_frag, frag_len=2346
RTL871X: rtw_wx_get_rts, rts_thresh=2347
RTL871X: rtw_wx_get_frag, frag_len=2346
RTL871X: rtw_wx_get_rts, rts_thresh=2347
RTL871X: rtw_wx_get_frag, frag_len=2346
ls: /mnt/CF/link2: No such file or directory
Send FIFO Cmd :trigger